Dry Carbon Fiber Window Lift Button Trim & Switch Covers for Tesla Model Y L
-
訂單滿 $149 免運費
-
30天免費退換貨
-
30 天價格保障
-
終身客戶支援
聯絡我們
Dry Carbon Fiber Window Lift Button Trim & Switch Covers for Tesla Model Y L
Real dry carbon fiber on the panel your fingers find first.
A ten-piece dry carbon fiber overlay set for the window lift button panels and door switch buttons on all four doors of the Tesla Model Y L. The factory switches, backlighting, and button travel stay exactly as they are. Only the surface changes.
Replaces the factory piano-black gloss
The window switch panel is the highest-contact surface on an interior door, and it shows every fingerprint and fingernail mark. Woven carbon breaks up that flat gloss black without touching the button layout or the backlight.
Dry carbon, not a printed pattern
Carbon fiber prepreg is molded and cured under heat and pressure, so the weave is part of the structure rather than a film printed on plastic. The twill carries real depth and direction as light moves across it.
Peel, press, done — and reversible
Every cover arrives with 3M double-sided adhesive already applied to the reverse side, plus an adhesion promoter wipe. No door panel removal, no drilling, and the original trim stays complete underneath if you ever want it back.
Ten pieces. Four doors. One weave direction.
A closer look at the details.
Material Construction
Carbon fiber prepreg — 2x2 twill carbon fabric pre-impregnated with epoxy resin — molded into a thin overlay shell. Because the layers are laid by hand into a closed mold, the twill runs in one consistent direction across every piece in the set.
Manufacturing Process
Prepreg is laid into the mold, then compression molded and cured under heat and pressure. Each piece is trimmed, sanded, and finished with a gloss clear coat before the 3M double-sided adhesive is applied to the reverse side.
Surface Finish
2x2 twill weave under a high-gloss, UV-stabilized clear coat. The gloss deepens the weave pattern and reads closest to the factory piano-black it replaces, which is why it is the finish shown throughout this page.
Flush edge and OEM-fit radius
Each cover is trimmed to a soft, OEM-fit radius where it meets the door panel and the button openings. There is no hard lip for a sleeve, a ring, or a cleaning cloth to catch on, and the cover sits flush with the surrounding trim rather than proud of it.
The reverse side carries die-cut 3M double-sided adhesive, protected by a red release liner until you are ready to press the cover down. The supplied adhesion promoter wipe matters most along the edges and on low-surface-energy areas — that is what keeps the perimeter flat through summer heat cycles.
View test results and conditions
Pending. Add test type, applicable SKU, result, comparison baseline, conditions, and evidence source once product-specific testing is available.
Check compatibility before ordering.
| Compatible Models | Tesla Model Y L (six-seat long-wheelbase Model Y) |
|---|---|
| Version / Production Range | Model Y L, from launch in August 2025 onward, including vehicles built at Giga Shanghai and, from July 2026, Giga Texas. |
| Not Compatible With | Tesla Model Y (2020–2024), including early 2025 production. Tesla Model 3 (2017–2023) and Model 3 Highland rear doors. Right-hand-drive vehicles — this set is molded for left-hand drive. |
| Clearance Requirements | Adds approximately 1 mm of thickness over the factory panel. No contact with the switch, the door pull, or the window glass; window travel, door release, and the child lock are unaffected. |
How do I identify my vehicle version?
Three checks in order. First, confirm the seating layout: the Model Y L is the six-seat, three-row version with two individual second-row seats, so a five-seat Model Y is not the same vehicle and this set will not fit. Second, check the production date on the driver-side B-pillar label or in the vehicle software information screen — this set covers Model Y L from its August 2025 launch. Third, compare the passenger door window switch panel: on the 2020–2024 Model Y that panel is dimensionally different from the newer layout. If you would rather not guess, send a photo of your door switch panel and your vehicle information screen to support@tesery.com before ordering and we will confirm.
Know what to prepare before installation.
Peel-and-press installation, roughly 15 minutes for all four doors.
- Mounting method: pre-applied 3M double-sided adhesive, with adhesion promoter supplied for the panel edges.
- Removal or drilling: none. No door panel removal, no drilling, and no modification to the factory trim.
- Recommended installer: DIY. The only skill involved is lining up the button openings before the tape touches the panel.
- After installation: keep the doors dry for the first 24 hours and avoid frequent window cycles while the adhesive sets. In cold weather, extend this to 72 hours.
Included in the Box
- Window lift switch panel trim covers × 4 — one for each door
- Door release and lock button covers × 6
- 3M double-sided adhesive, pre-applied to the reverse side of every cover
- Adhesion promoter wipe
Prepare Separately
- Clean microfiber cloth — one for cleaning, one for pressing
- Plastic trim tool and a hair dryer or heat gun, for removal only
- Adhesive remover, for cleaning residual tape if you later take the covers off
- 01Park the vehicle, switch off, and close the windows. Wipe each panel with the promoter wipe and let it flash off completely — dust and hand oil are what cause lifting edges. Then dry-fit every cover with the liner still on, starting at the driver door, and check the button openings and the weave direction against the other doors.
- 02Peel one corner of the red liner and hold that corner while you seat the opposite edge first. Press outward from the middle to push air ahead of the tape, working toward the open corner as you peel. Press firmly for 30 to 60 seconds, concentrating on the edges and the openings around each button.
- 03Check every edge for lift, trapped air, or obstruction of the switch, and confirm the backlight is still fully visible. Test the window travel and the door release, then press the whole set down once more. Keep the doors dry and out of direct sun for 24 hours.
A few more things to know.
Fitment help, warranty claims, and order support: support@tesery.com. Covered by a 30-day warranty against manufacturing defects.
How should I clean and care for this part?
Mild soap and water, applied with a soft microfiber cloth, is all this surface needs. Wipe, then dry immediately rather than letting water sit along the edges. Wax or a ceramic coating every two to three months keeps the clear coat working against UV.
Avoid alcohol, tar remover, solvent-based dressings, abrasive polish, and stiff brushes. Never scrub a dry panel with a dry cloth — that is what leaves fine scratches in a clear coat. Fingerprints show more on the gloss finish than they would on a matte one, and they wipe straight off. Long-term parking in direct sunlight will eventually dull or slightly yellow any carbon fiber clear coat, so a shaded spot or a UV protectant slows that down considerably.
Can the vehicle be returned to its original condition?
Yes. Warm the cover gently with a hair dryer on low, work a plastic trim tool or a length of fishing line under an edge, and lift slowly. Clean any residue with adhesive remover. Because nothing was cut or drilled, the factory panel underneath is untouched.
The adhesive itself is single-use: once removed, a cover needs fresh 3M tape before it can go back on. We do not describe these covers as re-usable without replacement tape.
Will it work with other aftermarket accessories?
These covers are designed to sit flush within the existing door panel, so they do not interfere with window travel, door release, or the child lock, and there is nothing else mounted on that surface to conflict with.
For the closest visual match, pair them with other TESERY dry carbon interior parts in the same finish. Weave direction and gloss level vary between suppliers, so mixing brands side by side in one cabin is the one combination we cannot guarantee.
What if the part does not fit or arrives damaged?
Contact support@tesery.com and include your order number, your vehicle model and production year, photos of the condition issue, and photos of the outer box and shipping label. Please check fitment against the panel before you remove the adhesive liner — once the liner is off, the covers cannot be resold as new, which affects whether a return can be accepted.
Every order is covered by a 30-day warranty against manufacturing defects such as delamination or a clear coat fault. Full return and refund conditions, including who covers return shipping, are set out in our refund policy.
重要通知：
如果安裝後遇到任何問題，請在拆除產品前先與我們聯繫。
提供車輛詳細資訊（型號/年份/車輛識別碼 VIN）以及照片或短影片，將有助於我們更快解決您的問題。
在故障排除前拆除或更改產品，可能會導致無法退貨或更換。
TESERY 退貨政策
我們致力於為您提供無憂且愉快的購物體驗。如果您需要退回商品，我們提供清楚且便利的退貨服務。
1.取消訂單
-
您可以在訂單寄出前申請取消訂單。
-
如果您的訂單已經寄出，我們會盡力攔截，但不保證一定成功。
-
請透過電子郵件或我們的線上客服提交取消申請。
2. 30 天退貨政策
您有權在收到商品之日起 30 天內申請退貨。為確保流程順利，請務必在這 30 天期限內聯絡我們並提出退貨申請。
3. 退貨資格
如要符合退款資格，退回的商品必須符合以下條件：
-
商品必須維持收到時的相同狀態——未穿戴、未使用、吊牌完整，並置於原包裝內。
-
須提供購買證明。
4. 退貨原因與相關費用
我們處理兩種類型的退貨：
-
品質問題或商品損壞：
-
若您收到的商品有瑕疵、損壞，或收到錯誤商品，請立即聯絡我們。我們將提供全額退款或換貨，並承擔所有相關費用。
-
-
非品質相關退貨（例如個人偏好）：
-
若因個人偏好而退貨（例如改變心意，或對顏色或款式不滿意），將收取 15% 的補貨費，且退貨運費由顧客負擔。
-
5. 退貨流程
如要開始退貨，請依照以下步驟操作：
-
聯絡我們：
-
寄送電子郵件至
support@tesery.com/ service@tesery.com 或使用我們的即時聊天功能告知我們您的退貨申請。
-
-
接收 instructions：
-
退貨申請獲核准後，我們會向您提供詳細的退貨 instructions，包括寄送地址與包裝指南。
-
-
將商品寄回：
-
請依照提供的指示將商品寄回。請注意，未事先申請退貨而直接寄回給我們的商品將不予受理。
-
6. 不可退貨商品
由於商品性質特殊，某些類型的商品不符合退貨資格：
-
客製化產品：例如明確標示為客製化產品的方向盤和車輪，不得因非品質相關問題退貨。
-
特定商品：包括禮品卡、危險物品或易燃液體／氣體。
如果您對特定商品是否符合資格有任何疑問，請在購買前聯絡我們。
7. 退款與換貨
-
退款：
-
我們收到並檢查您退回的商品後，會通知您退款是否已獲核准。核准的退款將在 1-5 個工作日內自動退回至您原先使用的付款方式。 實際入帳時間取決於您的銀行或信用卡公司。
-
-
換貨：
-
為最快確保您取得所需商品，我們建議您先退回現有商品；退貨獲得受理後，再另外購買新商品。
-
8. 售後支援要求
為確保公平且有效率地解決問題，客戶申請售後支援時必須提供必要資訊，包括但不限於：
- 車輛詳細資訊（車型、年份、VIN）
- 清楚描述問題
- 顯示問題的相關照片及／或簡短影片
請注意：
未提供所需資訊可能會使我們無法準確診斷問題，並可能導致退貨、退款或換貨處理延遲，甚至無法處理。
對於已安裝、改裝或在未事先溝通的情況下拆除的產品，若無法確認產品狀況，TESERY 保留拒絕退貨申請的權利。
