Dry Carbon Fiber Window Lift Button Trim & Switch Covers for Tesla Model Y L
-
149ドル以上のご注文で送料無料
-
30日間の無料返品・交換
-
30日間価格保証
-
生涯カスタマーサポート
お問い合わせください
Dry Carbon Fiber Window Lift Button Trim & Switch Covers for Tesla Model Y L
Real dry carbon fiber on the panel your fingers find first.
A ten-piece dry carbon fiber overlay set for the window lift button panels and door switch buttons on all four doors of the Tesla Model Y L. The factory switches, backlighting, and button travel stay exactly as they are. Only the surface changes.
Replaces the factory piano-black gloss
The window switch panel is the highest-contact surface on an interior door, and it shows every fingerprint and fingernail mark. Woven carbon breaks up that flat gloss black without touching the button layout or the backlight.
Dry carbon, not a printed pattern
Carbon fiber prepreg is molded and cured under heat and pressure, so the weave is part of the structure rather than a film printed on plastic. The twill carries real depth and direction as light moves across it.
Peel, press, done — and reversible
Every cover arrives with 3M double-sided adhesive already applied to the reverse side, plus an adhesion promoter wipe. No door panel removal, no drilling, and the original trim stays complete underneath if you ever want it back.
Ten pieces. Four doors. One weave direction.
A closer look at the details.
Material Construction
Carbon fiber prepreg — 2x2 twill carbon fabric pre-impregnated with epoxy resin — molded into a thin overlay shell. Because the layers are laid by hand into a closed mold, the twill runs in one consistent direction across every piece in the set.
Manufacturing Process
Prepreg is laid into the mold, then compression molded and cured under heat and pressure. Each piece is trimmed, sanded, and finished with a gloss clear coat before the 3M double-sided adhesive is applied to the reverse side.
Surface Finish
2x2 twill weave under a high-gloss, UV-stabilized clear coat. The gloss deepens the weave pattern and reads closest to the factory piano-black it replaces, which is why it is the finish shown throughout this page.
Flush edge and OEM-fit radius
Each cover is trimmed to a soft, OEM-fit radius where it meets the door panel and the button openings. There is no hard lip for a sleeve, a ring, or a cleaning cloth to catch on, and the cover sits flush with the surrounding trim rather than proud of it.
The reverse side carries die-cut 3M double-sided adhesive, protected by a red release liner until you are ready to press the cover down. The supplied adhesion promoter wipe matters most along the edges and on low-surface-energy areas — that is what keeps the perimeter flat through summer heat cycles.
View test results and conditions
Pending. Add test type, applicable SKU, result, comparison baseline, conditions, and evidence source once product-specific testing is available.
Check compatibility before ordering.
| Compatible Models | Tesla Model Y L (six-seat long-wheelbase Model Y) |
|---|---|
| Version / Production Range | Model Y L, from launch in August 2025 onward, including vehicles built at Giga Shanghai and, from July 2026, Giga Texas. |
| Not Compatible With | Tesla Model Y (2020–2024), including early 2025 production. Tesla Model 3 (2017–2023) and Model 3 Highland rear doors. Right-hand-drive vehicles — this set is molded for left-hand drive. |
| Clearance Requirements | Adds approximately 1 mm of thickness over the factory panel. No contact with the switch, the door pull, or the window glass; window travel, door release, and the child lock are unaffected. |
How do I identify my vehicle version?
Three checks in order. First, confirm the seating layout: the Model Y L is the six-seat, three-row version with two individual second-row seats, so a five-seat Model Y is not the same vehicle and this set will not fit. Second, check the production date on the driver-side B-pillar label or in the vehicle software information screen — this set covers Model Y L from its August 2025 launch. Third, compare the passenger door window switch panel: on the 2020–2024 Model Y that panel is dimensionally different from the newer layout. If you would rather not guess, send a photo of your door switch panel and your vehicle information screen to support@tesery.com before ordering and we will confirm.
Know what to prepare before installation.
Peel-and-press installation, roughly 15 minutes for all four doors.
- Mounting method: pre-applied 3M double-sided adhesive, with adhesion promoter supplied for the panel edges.
- Removal or drilling: none. No door panel removal, no drilling, and no modification to the factory trim.
- Recommended installer: DIY. The only skill involved is lining up the button openings before the tape touches the panel.
- After installation: keep the doors dry for the first 24 hours and avoid frequent window cycles while the adhesive sets. In cold weather, extend this to 72 hours.
Included in the Box
- Window lift switch panel trim covers × 4 — one for each door
- Door release and lock button covers × 6
- 3M double-sided adhesive, pre-applied to the reverse side of every cover
- Adhesion promoter wipe
Prepare Separately
- Clean microfiber cloth — one for cleaning, one for pressing
- Plastic trim tool and a hair dryer or heat gun, for removal only
- Adhesive remover, for cleaning residual tape if you later take the covers off
- 01Park the vehicle, switch off, and close the windows. Wipe each panel with the promoter wipe and let it flash off completely — dust and hand oil are what cause lifting edges. Then dry-fit every cover with the liner still on, starting at the driver door, and check the button openings and the weave direction against the other doors.
- 02Peel one corner of the red liner and hold that corner while you seat the opposite edge first. Press outward from the middle to push air ahead of the tape, working toward the open corner as you peel. Press firmly for 30 to 60 seconds, concentrating on the edges and the openings around each button.
- 03Check every edge for lift, trapped air, or obstruction of the switch, and confirm the backlight is still fully visible. Test the window travel and the door release, then press the whole set down once more. Keep the doors dry and out of direct sun for 24 hours.
A few more things to know.
Fitment help, warranty claims, and order support: support@tesery.com. Covered by a 30-day warranty against manufacturing defects.
How should I clean and care for this part?
Mild soap and water, applied with a soft microfiber cloth, is all this surface needs. Wipe, then dry immediately rather than letting water sit along the edges. Wax or a ceramic coating every two to three months keeps the clear coat working against UV.
Avoid alcohol, tar remover, solvent-based dressings, abrasive polish, and stiff brushes. Never scrub a dry panel with a dry cloth — that is what leaves fine scratches in a clear coat. Fingerprints show more on the gloss finish than they would on a matte one, and they wipe straight off. Long-term parking in direct sunlight will eventually dull or slightly yellow any carbon fiber clear coat, so a shaded spot or a UV protectant slows that down considerably.
Can the vehicle be returned to its original condition?
Yes. Warm the cover gently with a hair dryer on low, work a plastic trim tool or a length of fishing line under an edge, and lift slowly. Clean any residue with adhesive remover. Because nothing was cut or drilled, the factory panel underneath is untouched.
The adhesive itself is single-use: once removed, a cover needs fresh 3M tape before it can go back on. We do not describe these covers as re-usable without replacement tape.
Will it work with other aftermarket accessories?
These covers are designed to sit flush within the existing door panel, so they do not interfere with window travel, door release, or the child lock, and there is nothing else mounted on that surface to conflict with.
For the closest visual match, pair them with other TESERY dry carbon interior parts in the same finish. Weave direction and gloss level vary between suppliers, so mixing brands side by side in one cabin is the one combination we cannot guarantee.
What if the part does not fit or arrives damaged?
Contact support@tesery.com and include your order number, your vehicle model and production year, photos of the condition issue, and photos of the outer box and shipping label. Please check fitment against the panel before you remove the adhesive liner — once the liner is off, the covers cannot be resold as new, which affects whether a return can be accepted.
Every order is covered by a 30-day warranty against manufacturing defects such as delamination or a clear coat fault. Full return and refund conditions, including who covers return shipping, are set out in our refund policy.
重要なお知らせ：
取り付け後に問題が発生した場合は、製品を取り外す前に必ずご連絡ください。
車両の詳細（モデル／年式／VIN）と写真や短い動画を提供していただくと、問題解決がより迅速になります。
トラブルシューティング前に製品を取り外したり改造した場合、返品や交換の対象外となることがあります。
TESERY返品ポリシー
安心して快適にお買い物いただけるよう努めています。商品を返品する必要がある場合は、明確で便利な返品サービスをご利用いただけます。
1.注文のキャンセル
-
発送前であれば、ご注文のキャンセルをリクエストできます。
-
ご注文の商品がすでに発送されている場合、配送を止められるよう最善を尽くしますが、成功を保証するものではありません。
-
キャンセルリクエストは、メールまたはオンラインカスタマーサービスから送信してください。
2. 30日間返品ポリシー
商品を受け取った日から30日以内であれば、返品をリクエストできます。手続きを円滑に進めるため、この30日以内に当社へ連絡し、返品を開始してください。
3. 返品の適用条件
返金を受けるには、返品商品が以下の条件を満たしている必要があります：
-
商品は、お受け取り時と同じ状態である必要があります。未着用・未使用で、タグが付いており、元の梱包材に入っていることが条件です。
-
購入証明が必要です。
4. 返品理由と関連手数料
返品には次の2種類があります：
-
品質上の問題または破損した商品：
-
お受け取りになった商品に欠陥や破損がある場合、または注文と異なる商品が届いた場合は、直ちにご連絡ください。全額返金または交換品の提供を行い、関連する費用はすべて当社が負担します。
-
-
品質に関係しない返品（例：個人的な都合）：
-
個人的な都合（例：気が変わった、色やスタイルに不満がある）による返品の場合、15%の再入庫手数料が適用され、返品送料はお客様のご負担となります。
-
5. 返品手続き
返品を開始するには、以下の手順に従ってください：
-
お問い合わせ：
-
メールを送信する
support@tesery.com/ service@tesery.com または、ライブチャットを利用して返品リクエストをお知らせください。
-
-
手順を受け取る：
-
返品リクエストが承認されると、配送先住所や梱包ガイドラインなど、返品に関する詳しい手順をお送りします。
-
-
商品を返送する：
-
提供された手順に従って商品をご返送ください。事前に返品を申請せずに返送された商品は受け付けられませんのでご注意ください。
-
6. 返品不可の商品
商品の性質上、返品対象外となる商品があります。
-
カスタマイズ製品：ステアリングホイールやホイールなど、カスタム製品であることが明記されている商品は、品質に関係しない問題を理由とした返品はできません。
-
特定の商品：ギフトカード、危険物、可燃性の液体／ガスなどが含まれます。
特定の商品が返品対象となるかご不明な場合は、ご購入前にお問い合わせください。
7. 返金と交換
-
返金：
-
返品された商品を受け取り、検品が完了しましたら、返金が承認されたかどうかをお知らせします。承認された返金は、1～5営業日以内に元のお支払い方法へ自動的に処理されます。 最終的な入金時期は、ご利用の銀行またはクレジットカード会社によって異なります。
-
-
交換：
-
ご希望の商品を最も早く確実に入手するには、お手元の商品を返品し、返品が受理された後に新しい商品を別途ご購入いただくことをおすすめします。
-
8. アフターセールスサポートの要件
公平かつ効率的に問題を解決するため、アフターセールスサポートを依頼する際は、以下を含む必要な情報（これらに限りません）をご提供いただく必要があります。
- 車両情報（モデル、年式、VIN）
- 問題の明確な説明
- 問題を示す写真および／または短い動画
ご注意ください：
必要な情報をご提供いただけない場合、問題を正確に診断できず、返品、返金、または交換の処理に遅延が生じたり、処理できない場合があります。
事前の連絡なく製品が取り付け、改造、または取り外しされた場合、製品の状態を確認できないときは、TESERYは返品リクエストをお断りする権利を有します。
