Model Y Juniper Brake Caliper Covers Installation Guide

Installation

About an hour. No brake parts removed.

Everything happens on the outside of the caliper. The wheel comes off, the cover goes on, the wheel goes back. No brake line is opened, no fluid is lost, and nothing needs bleeding afterwards.

Time
45–60 min
All four wheels
Difficulty
3 of 5
Hand tools
Brake fluid
Not opened
No bleeding
Reversible
Unbolt
Original parts untouched

Full walkthrough, front and rear. Watch it once before you start, then work from the six steps below.

Before you start

Lay it all out first.

Half of all fitting problems are a wrong clip in the wrong corner. Check the contents against the list before the car goes up.

In the box
Two hex keys
Ball-head locating clips, coded R4 · R5 · L4 · L5
M6 socket-head bolts and washers
Spring retaining clips
Isopropyl cleaning wipes
From your garage
Jack and axle stands, or a lift
Torque wrench
21 mm socket for the wheel nuts
A torch — you are working in a wheel arch
Gloves. Brake dust is not harmless
Jacking a car is the part that injures people. Never put any part of yourself under a vehicle held only by a jack. If you are not confident with stands or a lift, have the wheels removed for you and do the rest yourself.
The sequence

Six steps per wheel.

Do one wheel completely before starting the next. Mixing two wheels at once is how clips end up on the wrong side.

01

Crack the wheel nuts on the ground.

Break the torque on each nut a quarter turn while the tyre still carries the car. Once the car is in the air the wheel spins and you have nothing to push against.

Leave all four wheels down for this step.
02

Lift, then take the wheel off.

Use the factory lift points and set a stand before you take the weight. Slide the removed wheel flat under the sill as a second line of defence — it costs nothing and it has saved people.

Never work under a car held only by a jack.
03

Clean the caliper face.

Brake dust is why covers work loose. Wipe the outer face and both mounting shoulders down with the wipe in the box, then let it flash off for a minute. Adhesive and clips both need a clean, dry surface.

Do not spray cleaner at the caliper or the piston boot.
04

Seat the locating clips.

Every clip is coded: R4, R5, L4, L5. R and L are the side of the car. 4 and 5 are the caliper position. Press the ball head into the socket on the inside of the cover first, then seat the clip body on the caliper shoulder.

If a clip will not sit down, it is the wrong position — not a tight fit.
05

Press the cover on.

Offer it up square and push until the ball heads click home. The leading edge should sit flush with no gap and no rock when you press the far corner.

If it rocks, a clip is not seated. Take it off and start again — do not pull it down with the bolts.
06

Torque the bolts.

Fit the M6 bolts and washers and bring them down in a cross pattern, a few turns at a time. Torque to the figure printed on the card in the box.

The thread is in the caliper bracket and the cover is aluminium. More is not better.
Before it goes back on the ground

Turn the wheel by hand. All the way round.

Refit the wheel, torque the nuts to Tesla's current specification, then rotate it through a full revolution before the car comes down. This is the step that matters and the step that gets skipped.

01
Clearance to the spokes, through the whole rotation
02
Clearance to the rotor, the hose and the bleed screw
03
No contact at full lock, either side
04
Both cover fixings still tight after the wheel is on
Wheel diameter alone tells you nothing. It is the spoke profile that closes the gap, which is why an aftermarket or deeply dished wheel can touch where a factory wheel clears.
After the first drive

Torque the wheels, then check it again.

A wheel torqued in the air can settle once it carries the car. Lower it first, then torque, then drive, then re-check the covers.

Wheel nuts
Tesla's current spec
Torqued on the ground, in a star pattern
Cover bolts
Re-check at 100 km / 60 mi
M6 into aluminium will take a set
Brake service
Unbolt, never pry
The fixings are left reachable on purpose
Close-up reference

The parts that are hard to see.

Clip seating, cover alignment and the torque sequence, filmed close enough to copy.

If something is not right

Four things that go wrong.

The cover will not sit flush
A clip is not seated, or the position code is wrong for that corner. Take the cover off and look at the clip before you touch a bolt. Drawing it down with the bolts is how the cover cracks and how a bolt pulls its thread.
There is a rattle over bumps
Check the M6 bolts first, then the clips. A clip that has come off its shoulder lets the cover move a millimetre, and a millimetre is enough to hear. Re-seat it and torque again.
The wheel catches the cover
Stop. Do not drive. Wheel diameter is not the deciding factor — spoke profile is. An aftermarket, dished or spaced wheel can close a gap that a factory wheel leaves open. Take the cover off and check again, or have it checked for you.
A bolt keeps coming loose
That usually means it has been over-torqued once already and the fastener is stretched. Replace the bolt. Do not add threadlocker to a stretched bolt — it hides the problem rather than fixing it.
Before you drive

These covers are decorative. They do not alter braking force, pedal travel or clearance, they are not a substitute for brake maintenance, and they fit factory calipers only. Nothing here requires the hydraulic circuit to be opened — if a job you are doing does, this page does not cover it.

Professional fitting is recommended wherever you are not confident lifting the car. The clearance check is the one step that cannot be skipped, and it is the easiest one to rush.

The product

Model Y brake caliper covers.

Front and rear covers in 6061-T6 aluminium, finished to match the car. If you are still deciding on a finish or checking fitment, the product page has the full specification and the current options.

View the Model Y caliper covers