Driving a Tesla Model Y is not just about the thrill of electric mobility but also about maintaining the pristine condition of your vehicle. One of the best ways to protect your car from dirt, mud, and road debris is by installing mud flaps. Mud flaps not only enhance the appearance of your vehicle but also provide practical protection for your wheels and undercarriage. In this guide, we’ll walk you through the process of installing mud flaps on your Tesla Model Y, ensuring a smooth and secure installation.
How to Install Tesla Model Y Mud Flaps
Required tools for installing Tesla Model Y mud flaps
TOOLS NEEDED
• Angled drill/screwdriver with 5/16" socket
• Locking pliers
• Marking pen
• Protective eyewear
• Tape measure or ruler
• Straight edge
• Cutting tool
PREPARING FOR INSTALLATION
A. Park on level ground with firm surface.
B. Check free space behind front tires when
fully turned. Ensure enough clearance to
accommodate 5/16" thick mud flaps.
C. Determine mud flap alignment and edge
orientation with wheels.
D. Insert bottom of mud flap into cardboard
guide and position in wheel well at desired
height to determine mounting screw locations.
Verify screws will contact solid surface.
INSTALLING MUD FLAPS
Preparation:
- Clean the mounting area with alcohol and make sure it is sufficiently dry before mounting
- Turn the steering wheel to the left side to allow room to work
Front fender installation:
- Remove fixings for front wheel arch liners
- Carefully remove the bottom push-pull clip that secures the front wheel arch liner using a push-pull clip removal tool or a one-piece screwdriver
- Shift the fender so that the locking tabs on the fender are free from the rear side of the front wing trim panel
- Install the new push-pull clips into the inner holes and push the plastic rivets inward to close the push-pull clips, making sure to install the inner push-pull clips first.
- Align the mudguard to the front wheel arch liners and body holes to ensure accurate alignment.
- Install the new push-pull clips into the outer holes and push the plastic rivets inward to close the push-pull clips.
Final Adjustment:
- Make sure fenders are level to avoid blind spots and contact with obstacles .
- Check wheelbase, especially for vehicles with modified wheels and suspension
Rear fender installation:
- Remove rear wheel arch liner fixings .
- Secure the rear fender to the vehicle body using the expansion anchors.
- Orient the fender logo towards the rear of the vehicle and secure with screws and washers.
- Adjust the position of the fender to ensure that it corresponds to the contours of the vehicle body.
Notes:
- Use offset or variable speed Phillips screwdrivers, flathead screwdrivers, and marking pens
- Avoid tightening with power tools, use only hand tools and avoid over-tightening
- Take care to avoid damaging vehicle components during installation
Common issues or safety precautions when installing mud flaps on Tesla Model Y
Avoiding Blind Spots and Obstacles: Care needs to be taken during installation to avoid contact with curbs, curb and over-compressed mudguard objects and to ensure that there are no obstacles around the vehicle.
Tool Selection: Offset or variable speed Phillips screwdrivers, flathead screwdrivers and marking pens are recommended. Avoid the use of power tools and use only hand tools to avoid over-tightening
Check wheelbase and suspension: Especially for vehicles with modified wheels and suspension, the wheelbase needs to be checked for proper fitment to ensure that the fenders do not interfere with the normal operation of the vehicle
Installation position: the fender should be flush with the ground to ensure that it is not too high or too low to affect the aerodynamics of the vehicle.
Material Selection: Choose high-quality fender materials such as polyurethane plastic or high-strength nylon, which are resistant to abrasion and corrosion.
Installation Steps:
- Loosen the set screw by the tire.
- Align the fender with the mounting position.
- Use the screws to secure the fender to the vehicle.
- Check the position of the fender and the tightness of the screws.
- Avoiding damage: Plastic fenders may break when encountering speed bumps, so it is advisable to choose a stronger material!
Maintenance and inspection: Regularly check the condition of the fenders and replace damaged or missing parts in time.
Safe Driving: After installing the fenders, make sure that they do not interfere with your driving
SAFETY AND MAINTENANCE
The operator can perform most of inspection and maintenance. It may be necessary to review the installation instructions.
• Periodically check all screws and nuts, retighten if needed.
• DO NOT hook up anything to mud flaps.
• If mud flap has been damaged, replace with new one.
View Video
Call to Action
Installing mud flaps on your Tesla Model Y is a simple yet effective way to protect your vehicle from road debris and enhance its overall appearance. By following the steps outlined in this guide, you can ensure a secure and professional-looking installation. Mud flaps are not only functional but also add a touch of customization to your vehicle. Whether you’re a DIY enthusiast or a first-time installer, this guide will help you get the job done right. Keep your Tesla Model Y looking and performing its best with the right accessories.
